SEISMIC JOINTS

Watertight expansion joint for car parks and any other places with or without traffic of slow vehicles.

JSV 4-02

MATERIAL : ALUMINIUM
COLOR: NATURAL, RAL COLORS
VERSION : FLAT & ANGLE.
Seismic expansion joint
Vertical installation on facade, wall and ceiling
For joint gaps from 50 to 200 mm

DESCRIPTION:

All-aluminium vertical expansion joint for facades, comprising pre-drilled aluminium side sections and an interchangeable section in the center, able to take up large multi-directional movements. A waterproof membrane is available to ensure protection against the elements. Specially suitable for quality finish requirements and for wide joints with large seismic movements.

Installation:

For vertical joints in facades with a gap up to 200 mm (larger dimensions available on request).

COMPOSING:

Section length of 3 lm. Aluminium side and central sections. Nit-rile membrane

ALUMINIUM

Material	Aluminium 6060	Aluminium 6063
Density	2,7	2,7
Elongation at break	min. 160 MPa	min. 215 MPa
Breaking limit	min. 215 MPa	min. 245 MPa
Elongation	min. 6 %	min. 6 %
Thermal conductivity at 20°C	190 W / m.°C	190 W / m.°C
Modulus of elasticity	70.000 MPa	70.000 MPa
Modulus of rigidity	27.000 MPa	27.000 MPa
Value by Poisson	0,33	0,33
Fire resistance	A 1	A 1

Nitrile

Material	Nitrile DIN 18541	Test Method
Shore A hardness	67 ± 5	ISO 868
Density	1,25	ISO R 1183
Tensile strength	≥ 10 MPa	ISO R 527-2
Elongation at break	≥ 350 %	ISO R 527-2
Elongation at tear at 23°C	≥ 350 %	DIN 53504
Tear-growth resistance	≥ 14 MPa	DIN 53504
Linear tolerance	± 0,7 %	DIN 16941
Linear expansion coefficient	15 – 17 x 10^-5 K^-1	DIN 53752
Fire resistance	B2	B2

REFERENCE	GAP (MM)	MOVEMENTS (MM)	VISIBLE WIDTH (MM)	TOTAL WIDTH (MM)	HEIGHT (MM)
JSV 4.02	W		S	B	H
4.02-040	40	25/-25	114	114	15,7
4.02-040 A	40	12,5/-12,5	61	77	15,7
4.02-050	50	39/-39	151	151	15,7
4.02-050 A	50	19,5/-19,5	85	101	15,7
4.02-060	60	39/-39	161	161	15,7
4.02-060 A	60	19,5/-19,5	95	111	15,7
4.02-080	80	39/-39	181	181	15,7
4.02-080 A	80	19,5/-19,5	115	131	15,7
4.02-100	100	39/-39	201	201	15,7
4.02-100 A	100	19,5/-19,5	135	151	15,7
4.02-120 A	120	39/-39	221	221	15,7
4.02-120 A	120	19,5/-19,5	155	171	15,7
4.02-150	150	39/-39	251	251	15,7
4.02-150 A	150	19,5/-19,5	185	201	15,7
4.02-180	180	39/-39	281	281	15,7
4.02-180 A	180	19,5/-19,5	215	231	15,7
4.02-200	200	39/-39	301	301	15,7
4.02-200 A	200	19,5/-19,5	235	251	15,7

The load-bearing capacity is always indicated for a joint in its initial position. In case of opening movements, the load-bearing capacity significantly reduces and the product will thus be only adapted for a light pedestrian traffic. The indicated load-bearing capacities are based on pneumatic wheels vehicles with a contact surface of 200×200 mm.

JSV 4-06

MATERIAL : ALUMINIUM, NITRILE.
FINISHES : BLACK, GREY, RAL COLORS
VERSION : FLAT & ANGLE.
Seismic expansion joint
Vertical installation on facade, wall and ceiling
For joint gaps up to 350 mm

DESCRIPTION:

Vertical expansion joint for wall, ceiling and facade for joint gaps up to 350 mm. This seismic expansion joint allows large multi-directional movements. Available in flat and angle versions

COMPOSING:

Section length of 3 lm. Aluminium side and central sections. Nitrile membrane

ALUMINIUM

Material	Aluminium 6060	Aluminium 6063
Density	2,7	2,7
Elongation at break	min. 160 MPa	min. 215 MPa
Breaking limit	min. 215 MPa	min. 245 MPa
Elongation	min. 6 %	min. 6 %
Thermal conductivity at 20°C	190 W / m.°C	190 W / m.°C
Modulus of elasticity	70.000 MPa	70.000 MPa
Modulus of rigidity	27.000 MPa	27.000 MPa
Value by Poisson	0,33	0,33
Fire resistance	A 1	A 1

Nitrile

Material	Nitrile DIN 18541	Test Method
Shore A hardness	67 ± 5	ISO 868
Density	1,25	ISO R 1183
Tensile strength	≥ 10 MPa	ISO R 527-2
Elongation at break	≥ 350 %	ISO R 527-2
Elongation at tear at 23°C	≥ 350 %	DIN 53504
Tear-growth resistance	≥ 14 MPa	DIN 53504
Linear tolerance	± 0,7 %	DIN 16941
Linear expansion coefficient	15 – 17 x 10^-5 K^-1	DIN 53752
Fire resistance	B2	B2

REFERENCE	GAP (MM)	MOVEMENTS (MM)	VISIBLE WIDTH (MM)	TOTAL WIDTH (MM)	HEIGHT (MM)
JSV 4.06	W		S	B	H
4.06-030	30	8 / -2	120	120	15
4.06-050	50	20 / -10	140	140	15
4.06-080	80	35 / -15	170	170	15
4.06-120	120	45 / -20	210	210	15
4.06-200	200	50 / -40	290	290	15
4.06-280	280	80 / -45	370	370	15
4.06-350	350	100 / -50	440	440	15

JSV 4-10

MATERIAL : ALUMINIUM.
FINISHES : NATURAL, RAL COLORS.
VERSION : FLAT & ANGLE.
Expansion joint special wide seismic movements
Vertical installation on facade, wall and ceiling
For joint gaps from 50 to 200 mm

DESCRIPTION:

All metal vertical seismic expansion joint for train stations, airports, shopping center… This range is design with springs to allow seismic movements.

COMPOSING:

Aluminium

ALUMINIUM

Material	Aluminium 6060	Aluminium 6063
Density	2,7	2,7
Elongation at break	min. 160 MPa	min. 215 MPa
Breaking limit	min. 215 MPa	min. 245 MPa
Elongation	min. 6 %	min. 6 %
Thermal conductivity at 20°C	190 W / m.°C	190 W / m.°C
Modulus of elasticity	70.000 MPa	70.000 MPa
Modulus of rigidity	27.000 MPa	27.000 MPa
Value by Poisson	0,33	0,33
Fire resistance	A 1	A 1

REFERENCE	GAP (MM)	MOVEMENTS (MM)	VISIBLE WIDTH (MM)	TOTAL WIDTH (MM)	HEIGHT (MM)
JSV 4.10	W		S	B	H
4.10-050	50	25 / -25	170	170	16,5
4.10-050 A	50	25 / -25	110	110	16,5
4.10-100	100	50 / -50	220	220	16,5
4.10-100 A	100	50 / -50	160	160	25
4.10-150	150	75 / -75	270	270	25
4.10-150 A	150	75 / -75	210	210	25
4.10-200	200	100 / -100	320	320	25
4.10-200 A	200	100 / -100	260	260	25

JSV 4-12

MATERIAL : ALUMINIUM.
FINISHES : NATURAL, RAL COLORS.
VERSION : FLAT & ANGLE.
Expansion joint special wide seismic movements
Vertical installation on facade, wall and ceiling
For joint gaps from 50 to 200 mm

DESCRIPTION:

All metal seismic expansion joint for ceilings. Flat and angle models are available

COMPOSING:

Aluminium

ALUMINIUM

Material	Aluminium 6060	Aluminium 6063
Density	2,7	2,7
Elongation at break	min. 160 MPa	min. 215 MPa
Breaking limit	min. 215 MPa	min. 245 MPa
Elongation	min. 6 %	min. 6 %
Thermal conductivity at 20°C	190 W / m.°C	190 W / m.°C
Modulus of elasticity	70.000 MPa	70.000 MPa
Modulus of rigidity	27.000 MPa	27.000 MPa
Value by Poisson	0,33	0,33
Fire resistance	A 1	A 1

REFERENCE	GAP (MM)	MOVEMENTS (MM)	VISIBLE WIDTH (MM)	TOTAL WIDTH (MM)	HEIGHT (MM)
JSV 4.12	W		S	B	H
4.12-050	50	25 / -25	170	170	16,5
4.12-050 A	50	25 / -25	110	110	16,5
4.12-100	100	50 / -50	220	220	16,5
4.12-100 A	100	50 / -50	160	160	16,5
4.12-150	150	75 / – 75	270	270	17,5
4.12-150 A	150	75 / – 75	210	210	17,5
4.12-200	200	100 / – 100	320	320	17,5
4.12-200 A	200	100 / – 100	260	260	17,5

JSV 4-14

MATERIAL : ALUMINIUM, NITRILE.
FINISHES : BLACK, GREY.
VERSION : FLAT & ANGLE.
Seismic expansion joint
Special suspended ceilings
For joint gaps from 30 to 100 mm

DESCRIPTION:

Expansion joint for false ceilings, comprising aluminium side sections and an interchangeable insert in the center, able to take up large multi-directional movements. Specially suitable for suspended ceilings.

INSTALLATION:

For joints in false ceilings or suspended ceilings with a gap up to 350 mm.

FINISHES AND SPECIAL PIECES:

Flat and corner (E). Black or gray insert. Other RAL colors available on request.

COMPOSING:

Section length of 4 m. Aluminium side angle sections. Top quality flexible PVC insert(flex).

ALUMINIUM

Material	Aluminium 6060	Aluminium 6063
Density	2,7	2,7
Elongation at break	min. 160 MPa	min. 215 MPa
Breaking limit	min. 215 MPa	min. 245 MPa
Elongation	min. 6 %	min. 6 %
Thermal conductivity at 20°C	190 W / m.°C	190 W / m.°C
Modulus of elasticity	70.000 MPa	70.000 MPa
Modulus of rigidity	27.000 MPa	27.000 MPa
Value by Poisson	0,33	0,33
Fire resistance	A 1	A 1

REFERENCE	GAP (MM)	MOVEMENTS (MM)	VISIBLE WIDTH (MM)	TOTAL WIDTH (MM)	HEIGHT (MM)
JSV 4.14	W		S	B	H
4.14-030	30	8 / – 2	60	60	50
4.14-050	50	20 / – 10	80	80	50
4.14-080	80	30 / – 15	110	110	50
4.14-100	100	45 / – 20	130	130	50

JSH 6-08

MATERIAL : ALUMINIUM.
COLOR : NATURAL.
VERSION : FLAT & ANGLE.
Seismic expansion joint
For intensive heavy-duty traffic
For joint gaps from 30 to 110 mm

DESCRIPTION:

All aluminium seismic floor expansion joint for indoor and outdoor applications. The two top aluminium components slide one into the other, which takes up any movement due to expansion and contraction. Suitable for all types of finish: concrete, screed, tiling, etc.

Installation:

For indoor and outdoor floor joints with a gap up to 100 mm. Suitable for heavy traffic of fork-lift truck on pneumatic tires, pallet trucks and intense traffic of light vehicles.

FINISHES AND SPECIAL PIECES:

Floor-to-floor type, and floor-to-wall type with exposed skirting. Vapor membrane as option (for heights > 20 mm), which can be supplied as whole length to avoid joining on site. Surface finish: anti-slip ribbed (R) or plain (G). Special finish with anti-slip nitrile inserts on request (426/RS range). Special parts on demand (T, X, L…).

COMPOSING:

Section length of 4 m. Nitrile vapor barrier. Aluminium side angle sections, pre-drilled

ALUMINIUM

Material	Aluminium 6060	Aluminium 6063
Density	2,7	2,7
Elongation at break	min. 160 MPa	min. 215 MPa
Breaking limit	min. 215 MPa	min. 245 MPa
Elongation	min. 6 %	min. 6 %
Thermal conductivity at 20°C	190 W / m.°C	190 W / m.°C
Modulus of elasticity	70.000 MPa	70.000 MPa
Modulus of rigidity	27.000 MPa	27.000 MPa
Value by Poisson	0,33	0,33
Fire resistance	A 1	A 1

Nitrile

Material	Nitrile DIN 18541	Test Method
Shore A hardness	67 ± 5	ISO 868
Density	1,25	ISO R 1183
Tensile strength	≥ 10 MPa	ISO R 527-2
Elongation at break	≥ 350 %	ISO R 527-2
Elongation at tear at 23°C	≥ 350 %	DIN 53504
Tear-growth resistance	≥ 14 MPa	DIN 53504
Linear tolerance	± 0,7 %	DIN 16941
Linear expansion coefficient	15 – 17 x 10^-5 K^-1	DIN 53752
Fire resistance	B2	B2

EFERENCE	GAP (MM)	MOVEMENTS (MM)	VISIBLE WIDTH (MM)	TOTAL WIDTH (MM)	HEIGHT (MM)
JSH 6.08	W		S	B	H
6.08-040	40	5 / -5	60	160	20
6.08-065	65	10 / -10	90	190	20
6.08-050	50	5 / -5	70	155	43 / 48 / 58 / 63 / 68 / 88 / 108
6.08-080	80	10 / -10	95	180	43 / 48 / 58 / 63 / 68 / 88 / 108
6.08-100	100	15 / -15	135	225	43 / 48 / 58 / 63 / 68 / 88 / 108

JSH 6-12

MATERIAL : ALUMINIUM.
COLOR : NATURAL.
VERSION : FLAT & ANGLE.
Seismic expansion joint
For intensive heavy-duty traffic
For joint gaps from 60 to 110 mm

DESCRIPTION:

All-metal floor expansion joint specially designed to withstand heavy loads: load handling equipment, lorries… Suitable for indoor and outdoor applications. The central elements allow significant expansion and contraction movements, as well as vertical shearing movements. Suitable for all types of finish: concrete, screed, tiling, etc.

Installation:

For indoor and outdoor floor joints with a gap up to 200 mm, with large amount of movements and heavy loads. Suitable for heavy traffic of fork-lift truck on solid tires , loads of up to 6 tonnes/axle on pneumatic tires, lorries, pallet trucks and intense traffic of light vehicles.

FINISHES AND SPECIAL PIECES:

Floor-to-floor and floor-to-wall types. Anti-slip ribbed surface. This product is supplied ready to install, with spacers that must be removed after installation on the floor.

COMPOSING:

Section length of 3 m. Aluminium side angle sections, pre-drilled.

ALUMINIUM

Material	Aluminium 6060	Aluminium 6063
Density	2,7	2,7
Elongation at break	min. 160 MPa	min. 215 MPa
Breaking limit	min. 215 MPa	min. 245 MPa
Elongation	min. 6 %	min. 6 %
Thermal conductivity at 20°C	190 W / m.°C	190 W / m.°C
Modulus of elasticity	70.000 MPa	70.000 MPa
Modulus of rigidity	27.000 MPa	27.000 MPa
Value by Poisson	0,33	0,33
Fire resistance	A 1	A 1

REFERENCE	GAP (MM)	MOVEMENTS (MM)	VISIBLE WIDTH (MM)	TOTAL WIDTH (MM)	HEIGHT (MM)
JSH 6.12	W		S	B	H
6.12-060	60	± 15	80	170	18 / 35 / 50 / 80
6.12-080	80	+20 / -20	110	250	50 / 80

JSH 6-14

MATERIAL : ALUMINIUM.
COLOR : NATURAL.
VERSION : FLAT & ANGLE.
Reinforced seismic expansion joint
For intensive heavy-duty traffic
For joint gaps from 50 to 200 mm

DESCRIPTION:

Installation:

For indoor and outdoor floor joints with a gap up to 200 mm, with large amount of movements and heavy loads. Suitable for heavy traffic of fork-lift truck on solid tires, loads of up to 6 tonnes/axle on pneumatic tires, lorries, pallet trucks and intense traffic of light vehicles.

FINISHES AND SPECIAL PIECES:

Floor-to-floor and floor-to-wall types. Anti-slip ribbed surface. This product is supplied ready to install, with spacers that must be removed after installation on the floor.

COMPOSING:

Section length of 3 m. Aluminium side angle sections, pre-drilled.

ALUMINIUM

Material	Aluminium 6060	Aluminium 6063
Density	2,7	2,7
Elongation at break	min. 160 MPa	min. 215 MPa
Breaking limit	min. 215 MPa	min. 245 MPa
Elongation	min. 6 %	min. 6 %
Thermal conductivity at 20°C	190 W / m.°C	190 W / m.°C
Modulus of elasticity	70.000 MPa	70.000 MPa
Modulus of rigidity	27.000 MPa	27.000 MPa
Value by Poisson	0,33	0,33
Fire resistance	A 1	A 1

REFERENCE	GAP (MM)	MOVEMENTS (MM)	VISIBLE WIDTH (MM)	TOTAL WIDTH (MM)	HEIGHT (MM)
JSH 6.14	W		S	B	H
6.14-050	50	± 30	255	255	20
6.14-100	100	± 30	305	305	20
6.14-150	150	± 30	360	360	20
6.14-200	200	± 30	410	410	20

JSH 6-16

MATERIAL : ALUMINIUM.
COLOR : NATURAL.
VERSION : FLAT & ANGLE.
Seismic expansion joint
For wide gaps
For joint gaps from 110 to 250 mm

DESCRIPTION:

Seismic floor expansion joint for indoor and outdoor applications, comprising two side angle sections and a central element of thick section made of aluminium, able to take up significant expansion and contraction movements, as well as vertical shearing movements. Suitable for all types of finish: concrete, screed, tiling, etc.

Installation:

For indoor and outdoor floor joints with a gap up to 250 mm. Suitable for intense traffic of light vehicles.

FINISHES AND SPECIAL PIECES:

Floor-to-floor and floor-to-wall types. Anti-slip ribbed surface. This product is supplied ready to install, with spacers that must be removed after installation on the floor. Special parts on demand (T, X, L…).

COMPOSING:

Section length of 2 m. Aluminium side angle sections, pre-drilled.

ALUMINIUM

Material	Aluminium 6060	Aluminium 6063
Density	2,7	2,7
Elongation at break	min. 160 MPa	min. 215 MPa
Breaking limit	min. 215 MPa	min. 245 MPa
Elongation	min. 6 %	min. 6 %
Thermal conductivity at 20°C	190 W / m.°C	190 W / m.°C
Modulus of elasticity	70.000 MPa	70.000 MPa
Modulus of rigidity	27.000 MPa	27.000 MPa
Value by Poisson	0,33	0,33
Fire resistance	A 1	A 1

REFERENCE	GAP (MM)	MOVEMENTS (MM)	VISIBLE WIDTH (MM)	TOTAL WIDTH (MM)	HEIGHT (MM)
JSH 6.16	W		S	B	H
6.16-110	110	+20 / -20	130	250	35 / 50 / 80
6.16-250	250	+50 / -50	300	410	50 – 80

JSH 6-18

MATERIAL : ALUMINIUM.
COLOR : NATURAL.
VERSION : FLAT & ANGLE.
Joint de dilatation sismique
Spécial grandes largeurs
For opening joints between 135 et 340 mm

DESCRIPTION:

All-aluminium seismic floor expansion joint for indoor and outdoor applications. The two aluminium inner components slide one into the other, which takes up any movement due to expansion and contraction. Upper components made of aluminium, with the option of a nitrile strip for leveling. Suitable for all types of finish: concrete, screed, tiling, etc

Installation:

For indoor and outdoor floor joints with a gap up to 340 mm. Suitable for intense traffic of pedestrians and light trolleys (airport, supermarkets…), as well as traffic of light vehicles.

FINISHES AND SPECIAL PIECES:

Floor-to-floor type, and floor-to-wall type with exposed skirting (type A) and hidden skirting (type AV). Ribbed anti-slip surface. Nitrile strip for leveling as option. Special finish with anti-slip nitrile inserts on request. Special parts on demand (T, X, L…).

COMPOSING:

Section length of 4 m. Aluminium side angle sections, pre-drilled. Nitrile strip as option.

ALUMINIUM

Material	Aluminium 6060	Aluminium 6063
Density	2,7	2,7
Elongation at break	min. 160 MPa	min. 215 MPa
Breaking limit	min. 215 MPa	min. 245 MPa
Elongation	min. 6 %	min. 6 %
Thermal conductivity at 20°C	190 W / m.°C	190 W / m.°C
Modulus of elasticity	70.000 MPa	70.000 MPa
Modulus of rigidity	27.000 MPa	27.000 MPa
Value by Poisson	0,33	0,33
Fire resistance	A 1	A 1

RE+D3:I8FERENCE	GAP (MM)	MOVEMENTS (MM)	VISIBLE WIDTH (MM)	TOTAL WIDTH (MM)	HEIGHT (MM)
JSH 6.18	W		S	B	H
6.18-135	135	± 20	165	255	43 / 48 / 58 / 63 / 68 / 88
6.18-210	210	± 50	250	340	43 / 48 / 58 / 63 / 68 / 88
6.18-250	250	± 60	280	370	43 / 48 / 58 / 63 / 68 / 88
6.18-340	340	± 75	375	465	43 / 48 / 58 / 63 / 68 / 88

JSH 6-20

MATERIAL : ALUMINIUM.
COLOR : NATURAL.
VERSION : FLAT & ANGLE.
Seismic expansion joint
For wide gaps
For joint gaps from 135 to 340 mm

DESCRIPTION:

All-aluminium seismic floor expansion joint for indoor and outdoor applications. The two aluminium inner components slide one into the other, which takes up any movement due to expansion and contraction. Interchangeable upper components made of aluminium, with the option of a nitrile strip for leveling. Suitable for all types of finish: concrete, screed, tiling, etc.

Installation:

For indoor and outdoor floor joints with a gap up to 340 mm. Suitable for intense traffic of pedestrians and light trolleys (airport, supermarkets…), as well as traffic of light vehicles.

FINISHES AND SPECIAL PIECES:

COMPOSING:

ALUMINIUM

Material	Aluminium 6060	Aluminium 6063
Density	2,7	2,7
Elongation at break	min. 160 MPa	min. 215 MPa
Breaking limit	min. 215 MPa	min. 245 MPa
Elongation	min. 6 %	min. 6 %
Thermal conductivity at 20°C	190 W / m.°C	190 W / m.°C
Modulus of elasticity	70.000 MPa	70.000 MPa
Modulus of rigidity	27.000 MPa	27.000 MPa
Value by Poisson	0,33	0,33
Fire resistance	A 1	A 1

REFERENCE	GAP (MM)	MOVEMENTS (MM)	VISIBLE WIDTH (MM)	TOTAL WIDTH (MM)	HEIGHT (MM)
JSH 6.20	W		S	B	H
6.20-135	135	± 20	195	255	32 / 45,5
6.20-210	210	± 50	280	380	32 / 45,5
6.20-250	250	± 60	310	410	32 / 45,5
6.20-340	340	± 75	405	505	32 / 45,5

JSH 6-22

MATERIAL : ALUMINIUM.
COLOR : NATURAL.
VERSION : FLAT & ANGLE.
Seismic expansion joint
For wide movements : 50 %
For joint gaps from 50 to 200 mm

DESCRIPTION:

SPECOM’s JSH 6.22 seismic expansion joint and fire stop expansion joint comprises side angle sections and a central plate made of aluminium. It is able to take up large expansion and contraction movements, as well as vertical shearing movements, and is also suitable for all types of finish: concrete, screed, tiling, etc.

Installation:

The JSH 6.22 seismic expansion joint and fire stop expansion joint can be used for indoor and outdoor floor joints where a gap of up to 200 mm, with significant movement, is present. It is suitable for pedestrian and light trolley traffic.

FINISHES AND SPECIAL PIECES:

SPECOM’s JSH 6.22 range includes floor-to-floor (JSH 6.22) and floor-to-wall (JSH 6.22A) versions, with anti-slip ribbed surfaces. Optional waterproof membranes, with the potential to integrate a drainage system to recover liquid, are also available. Moreover, the JSH 6.22 seismic expansion joint and fire stop expansion joint range can be used in association with vertical joints that offer the same finish and movement range (type JSV 4.02 or other).

COMPOSING:

The JSH 6.22 seismic expansion joint and fire stop expansion joint comes in 3m section lengths, and features aluminium side angle sections and middle plate.

ALUMINIUM

Material	Aluminium 6060	Aluminium 6063
Density	2,7	2,7
Elongation at break	min. 160 MPa	min. 215 MPa
Breaking limit	min. 215 MPa	min. 245 MPa
Elongation	min. 6 %	min. 6 %
Thermal conductivity at 20°C	190 W / m.°C	190 W / m.°C
Modulus of elasticity	70.000 MPa	70.000 MPa
Modulus of rigidity	27.000 MPa	27.000 MPa
Value by Poisson	0,33	0,33
Fire resistance	A 1	A 1

REFERENCE	GAP (MM)	MOVEMENTS (MM)	VISIBLE WIDTH (MM)	TOTAL WIDTH (MM)	HEIGHT (MM)
JSH 6.22	W		S	B	H
6.22-050	50	25 / -25	170	170	27
6.22-100	100	50 / – 50	250	250	27
6.22-150	150	75 / – 75	320	320	27
6.22-200	200	100 / – 100	420	420	27
6.22-050 A	50	25 / – 25	125	125	27
6.22-100 A	100	50 / – 50	210	210	27
6.22-150 A	150	75 / – 75	305	305	27
6.22-200 A	200	100 / – 100	408	408	27

JSH 6-24

MATERIAL : STAINLESS STEEL.
COLOR : NATURAL.
VERSION : FLAT & ANGLE.
Seismic expansion joint
For wide movements : 50 %
For joint gaps from 50 to 200 mm

DESCRIPTION:

Seismic floor expansion joint for large movements, comprising the side angle sections and a central plate made of stainless steel, able to take up expansion and contraction movements, as well as vertical shearing movements. Suitable for all types of finish: concrete, screed, tiling, etc.

Installation:

For indoor and outdoor floor joints with a gap up to 200 mm (please enquirer if more width is required), with large amount of movements. SVF joints are particularly suitable for harsh environments such as the seaside, kitchens, swimming pools, water parks and thalassotherapy spas. Suitable for non-intense traffic of light vehicles, pedestrians and light trolleys.

FINISHES AND SPECIAL PIECES:

Floor-to-floor JSH 6.24 type , and floor-to-wall JSH 6.24 A type Anti-slip ribbed stainless steel. Waterproof membrane as option, with possibility of integrating drainage system to recover the liquid. SVF joints can be matched to vertical joints in terms of finish and movement range (please enquirer).

COMPOSING:

Section length of 3 m. Stainless steel side angle sections and middle plate.

STAINLESS STEEL

Material	Inox 304
Density	7,9
Electrical resistivity	0.73
Specific heat	500
Thermal conductivity	15 W / m.°C
Modulus of elasticity at 20°C	200 MPa
Tear-growth resistance	500 – 700 MPa
Tensile strength	782 MPa
Elongation at break	45%
Hardness Vickers	160 – 200 HV

REFERENCE	GAP (MM)	MOVEMENTS (MM)	VISIBLE WIDTH (MM)	TOTAL WIDTH (MM)	HEIGHT (MM)
JSH 6.22	W		S	B	H
6.22-050	50	25 / -25	170	170	25
6.22-100	100	50 / – 50	250	250	25
6.22-150	150	75 / – 75	320	320	25
6.22-200	200	100 / – 100	420	420	25
6.22-050 A	50	25 / – 25	125	125	25
6.22-100 A	100	50 / – 50	210	210	25
6.22-150 A	150	75 / – 75	305	305	25
6.22-200 A	200	100 / – 100	408	408	25

JSH 6-26

MATERIAL : ALUMINIUM.
COLOR : NATURAL.
VERSION : FLAT & ANGLE.
Seismic expansion joint
Special flexible floors
For joint gaps from 50 to 200 mm

DESCRIPTION:

Seismic floor expansion joint for large movements, comprising the side angle sections and a central plate made of stainless steel, able to take up expansion and contraction movements, as well as vertical shearing movements. . Suitable for all types of finish: concrete, screed, tiling, etc.

Installation:

For indoor and outdoor floor joints with a gap up to 200 mm (please enquirer if more width is required), with large amount of movements. JSH 6.26 joints are particularly suitable for hospitals, schools, etc. Suitable for intense pedestrians and light trolleys traffic.

FINISHES AND SPECIAL PIECES:

Floor-to-floor Series JSH 6.26 , and floor-to-wall Series JSH 6.26 A Anti-slip ribbed stainless steel. Waterproof membrane as option, with possibility of integrating drainage system to recover the liquid. JSH 6.24 joints can be matched to vertical joints in terms of finish and movement range (please enquirer).

COMPOSING:

Section length of 3 lm. Stainless steel side angle sections and middle plate.

ALUMINIUM

Material	Aluminium 6060	Aluminium 6063
Density	2,7	2,7
Elongation at break	min. 160 MPa	min. 215 MPa
Breaking limit	min. 215 MPa	min. 245 MPa
Elongation	min. 6 %	min. 6 %
Thermal conductivity at 20°C	190 W / m.°C	190 W / m.°C
Modulus of elasticity	70.000 MPa	70.000 MPa
Modulus of rigidity	27.000 MPa	27.000 MPa
Value by Poisson	0,33	0,33
Fire resistance	A 1	A 1

REFERENCE	GAP (MM)	MOVEMENTS (MM)	VISIBLE WIDTH (MM)	TOTAL WIDTH (MM)	HEIGHT (MM)
JSH 6.26	W		S	B	H
6.26-050	50	+30 / -50	170	330	40
6.26-100	100	+50 / -50	220	380	40
6.26-150	150	+80 / -100	330	490	40
6.26-200	200	+80 / -100	330	490	40
6.26-050 A	50	+40 / -30	125	205	40
6.26-100 A	100	+40 / -30	175	255	40
6.26-150 A	150	+55 / -60	240	320	40
6.26-200 A	200	+55 / -80	265	345	40

JSH 6-28

MATERIAL : ALUMINIUM, STAINLESS STEEL.
COLOR : NATURAL.
VERSION : FLAT.
Seismic expansion joint
Special tiles and stones
For joint gaps from 50 to 150 mm

DESCRIPTION:

Seismic floor expansion joint, comprising the side angle sections and a central plate made of stainless steel, able to take up expansion and contraction movements, as well as vertical shearing movements. Suitable for all types of hard floors (tiles, stone, marble, etc.), but can also be used with flexible floors or carpet.

Installation:

For indoor and outdoor floor joints with a gap up to 200 mm, with large amount of movements. Suitable for traffic of pedestrians and light trolleys.

FINISHES AND SPECIAL PIECES:

Floor-to-floor type only. The central plate takes the mortar on which the floor covering in laid. Once the floor covering is laid, the joint is practically invisible; only two stainless steel sections remain exposed. Waterproof membrane as option, with possibility of integrating drainage system to recover the liquid. JSH 6.28 joints can be matched to vertical joints of similar finish and with the same movement range (please enquirer).

COMPOSING:

Section length of 3 m. Aluminium side angle sections and stainless steel middle plate.

STAINLESS STEEL

Material	Inox 304
Density	7,9
Electrical resistivity	0.73
Specific heat	500
Thermal conductivity	15 W / m.°C
Modulus of elasticity at 20°C	200 MPa
Tear-growth resistance	500 – 700 MPa
Tensile strength	782 MPa
Elongation at break	45%
Hardness Vickers	160 – 200 HV

REFERENCE	GAP (MM)	MOVEMENTS (MM)	VISIBLE WIDTH (MM)	TOTAL WIDTH (MM)	HEIGHT (MM)
JSH 6.28	W		S	B	H
6.28-050	50	30 / – 24	170	210	62
6.28-100	100	30 / – 24	220	260	62